Water Proofing

Bitumen Coating, Bitumen Paint, Cement Based, Plugging, Protective Coatings, Waterstops



RUBBERISED BITUMEN EMULSION
Bitumen rubber latex compound. Waterproof coating to concrete prior to backfilling. Sandwich damp proof membrane. Repairs cracks in black top surfacing and concrete.
1-2m per litre per coat. 210 and 25 litre.


BLACK BITUMEN PAINT
Bitumen paint to BS3416 Part 1. A general purpose bituminous paint for waterproofing and weather protecting steelwork & concrete


WATERPROOF CEMENT BASED COATING
Designed for masonry and concrete. Designed to be brush or spray applied. Also available in pails on request. Water Bylaws approved and BT approval.


LEAK STOPPING
Rapid set accelerator for OPC plugs
Sika 2 + Sika 4A


PROTECTIVE COATINGS
Selection of other coatings available on request. Weatherproof and decorative coatings with a choice of technical properties.

Supa-Swell XL


Supa-Swell XL waterstop is designed to stop water infiltration through cast-in-place concrete construction joints by expanding upon contact with water to form a positive seal against the concrete.
Supa-Swell XL is a polymeric hydrophilic waterstop or waterbar composed of natural sodium bentonite clay and butyl rubber. It is 20mm x 25mm in section and is supplied as 5 metre rolls.
It can be simply fixed by a suitable adhesive bonding or by mesh and masonry nails.
SUPA-SWELL waterstop is harmless to the environment.
Variations of waterstop/waterbar are available on request, ie delayed reaction and salt water suitability.






PVC Waterbar & Junction Pieces


PVC WATERBAR is used in construction or expansion joints in concrete. It is cast in to both sections of concrete and creates a flexible seal across the joint. It is supplied in various widths and lengths per roll.
Installation of the waterbar may require JUNCTION PIECES. This requires a jointing jig and hot knife to be used as illustrated to melt and seal the waterbar and junction pieces together.

Waterproofing Membrane by CETCO


CAN BE INSTALLED IN ALMOST ANY WEATHER

Unlike conventional sheet waterproofing membranes, Voltex® can be applied in poor weather, ie cold, raining, even snow! This substantially reduces delays in schedule during the winter months. It’s construction means there is no need for tapes or protection boards and normal site activity need not be disrupted during installation, offering savings over alternative waterproofing membrane systems.





Voltex® Download
SIMPLE INSTALLATION
Normal sheet waterproofing membranes require complex installation to allow for complicated detailing.

The details are not only time consuming, but present areas in the future. Voltex® is far easier to install not only offering a time saving but also eliminating a potential source of future problems.
  • Voltex® can be applied in virtually all climates, even in the snow.
  • Voltex® can be applied uniquely to virtually all property line situations
    (piles, steel, existing masonry etc.)
  • Voltex® doesn’t require the temperature to be 5ºC and rising.
  • Voltex® doesn’t require a clean, dry, smooth, dust and frost free environment in which to be applied.
  • Voltex® doesn’t require the purchase of seam tapes which need a dry & dust free environment in which to be applied
  • Voltex® doesn’t require the need of a bituminous salve edge which may need to be rolled or smoothed.
  • Voltex® doesn’t require the use of solvented bituminous primers in any circumstances.
  • Voltex® doesn’t require the need for ‘gentle torching’ to remove moisture from the concrete and improve adhesion.
  • Voltex® doesn’t require the use or purchase of liquid bituminous compounds, prefabricated corner pieces & ‘L’ sections, top hats, mesh and detail strips.
  • Voltex® doesn’t require the use of protection boards or often even blinding.

CETCO

VOLTEX® WATERPROOFING SYSTEM
CETCO COMMITMENT
CETCO’s commitment to quality products, service and technical back-up is formally recognized through Quality Certification in various national and international standards (including BBA Certification), backed up by the experience of our parent company, AMCOL International, the largest bentonite producer in the world. Our group representation currently extends to over sixty countries.

Membranes, Building Films, Polythene Sheets


WATERPROOFING

SELF ADHESIVE WATERPROOF MEMBRANES (BITUTHENE TYPE)
FILLETS
PROTECTION BOARDS
WALL DRAINS.







WATERPROOFING MEMBRANES
SELF ADHESIVE WATERPROOFING MEMBRANES
Waterproof membranes are laminates of various plastic films and reinforcements coated with bitumen/polymer adhesives to provide a tough self-adhesive waterproof membrane sheeting. Can also be provided with integral foil layer to prevent the passage of methane and radon.
Supa-Sheet Data PDFSupa-Sheet COSHH PDF



BUILDING FILMS – SPECIALIST USE
High Quality Polyethylene Vapour Membrane for use in concrete slabs. Available in various grades to suit BBA certification or general Building Regulations and PIFA grade.




ECONOMICAL CLEAR POLYTHENE SHEET
For general site use. Rolls when unfolded are approximately 4 x 25m in size. For general protective uses on construction sites.

(Concrete curing, temporary glazing, protection of equipment and materials etc.)








Search